Quick answer: a 1,500 sq ft house in a moderate climate needs about 27,000 BTU, a 2.5 ton unit. A 2,000 sq ft house needs about 36,000 BTU, a 3 ton unit. Hot climates move up about half a ton per 1,000 sq ft.
AC size by house square feet
Standard central AC size for an average house with 8-foot ceilings and normal sun. Pick a size for the full breakdown.
| House size | Cool summers | Moderate | Hot | Desert |
|---|---|---|---|---|
| 1,000 sq ft | 1.5 ton | 1.5 ton | 2 ton | 2.5 ton |
| 1,200 sq ft | 1.5 ton | 2 ton | 2.5 ton | 2.5 ton |
| 1,500 sq ft | 2 ton | 2.5 ton | 3 ton | 3.5 ton |
| 1,800 sq ft | 2.5 ton | 3 ton | 3.5 ton | 4 ton |
| 2,000 sq ft | 2.5 ton | 3 ton | 3.5 ton | 5 ton |
| 2,500 sq ft | 3 ton | 4 ton | 5 ton | Two systems |
| 3,000 sq ft | 4 ton | 5 ton | Two systems | Two systems |
Room AC or whole-house AC?
This calculator is for central systems and ducted heat pumps that cool every room through ducts. For one room, a window unit or a single mini split head, use the room BTU calculator instead. It follows the ENERGY STAR room chart, which gives lower figures for big open rooms because they have less wall and window area per square foot than a whole house with hallways, bedrooms and ducts.
What pushes the size up or down
- Windows. Large west and south-facing windows add more heat than anything else. Choose very sunny if the afternoon sun hits big glass areas.
- Insulation and air leaks. An older house with little attic insulation and drafty windows can need 15% to 30% more capacity than the same house after an upgrade.
- Ducts in the attic. Leaky or uninsulated ducts in a hot attic waste a share of the cooling before it reaches the rooms. Sealing them is often cheaper than a bigger unit.
- Ceiling height. Vaulted ceilings and two-story foyers add volume to cool.
How this calculator works
Whole-house loads here use a rule of thumb: BTU per square foot of conditioned floor, chosen by climate, for an 8-foot ceiling and average insulation.
Cooling, by summer climate:
- Cool summers: 15 BTU per sq ft
- Moderate: 18 BTU per sq ft
- Hot: 22 BTU per sq ft
- Very hot or desert: 26 BTU per sq ft
Good insulation takes 15% off and poor insulation adds 15%. Ceilings above 8 feet scale the load by the extra height. A very sunny house adds 10% to cooling and a mostly shaded one takes 10% off. Results are rounded to the nearest 100 BTU. A standard size is the smallest one that covers at least 95% of the load.
These figures sit at the careful end of published rules of thumb. Older charts that quote 30 to 60 BTU per square foot for heating, or a ton for every 400 to 500 square feet everywhere, tend to oversize equipment in today's better-insulated homes.
A rule of thumb gets you into the right size range and helps you check a quote. Before buying a central system, ask the contractor for an ACCA Manual J load calculation. It accounts for your windows, orientation, air leakage, ducts and local design temperatures.
Frequently asked questions
What size AC unit do I need for my house?
In a moderate climate with average insulation, plan on about 18 BTU per square foot: roughly a 2-ton unit for 1,200 sq ft, 2.5 tons for 1,500 sq ft and 3 tons for 2,000 sq ft. Hot climates need about a fifth more. Use the calculator for your house.
How many square feet does a ton of AC cool?
About 667 sq ft per ton in a moderate climate, 545 sq ft in a hot one and 462 sq ft in a desert climate, for an average home with 8-foot ceilings.
Is a bigger AC unit better?
No. An oversized central system cools the house in short bursts, so it removes less humidity, runs less efficiently and wears faster. Rooms far from the air handler can still be uncomfortable. Pick the size the load calls for.
What is the largest residential AC size?
Most residential central air conditioners and heat pumps stop at 5 tons (60,000 BTU). Larger houses use two systems, often one per floor, which also makes each floor easier to control.
Should I just replace my old unit with the same size?
Not automatically. Many older systems were oversized, and new windows, insulation or air sealing lower the load. Check the size here and ask your contractor for a Manual J calculation before you buy.